2022 Updated ASQ CRE Dumps PDF - Want To Pass CRE Fast
CRE Practice Exam Dumps - 99% Marks In ASQ Exam
NEW QUESTION 107
In an analysis of variance, which of the following distributions is the basis for determining whether the variance estimates are all from the same population?
Response:
- A. Student's t
- B. Normal
- C. Chi square.
- D. F
Answer: D
NEW QUESTION 108
Which of the following CANNOT be classified as a computer output device?
Response:
- A. Printer.
- B. The keyboard.
- C. Disc drive unit.
- D. Magnetic tape unit.
Answer: B
NEW QUESTION 109
Failure data are analyzed and a proportion of items survive to the end of the test. Data on these types of samples are referred as:
Response:
- A. Censored Data.
- B. Parameter data
- C. Control data
- D. Non-parameter data.
Answer: A
NEW QUESTION 110
The failure rate for an IC chip is 0.0023 per hour of operation. Calculate the MTBF given that the failure rate is constant.
Response:
- A. 486 hrs
- B. 43 hrs
- C. 434.78 hrs
- D. 37.6 hrs
Answer: C
NEW QUESTION 111
Human factors in product safety planning are assessed for which of the following reasons?
I. To allocate the proper balance between man and machine.
II. To address the limitations of human beings.
III. To determine the user hardware interaction.
Response:
- A. III only
- B. I and III only
- C. I and II only
- D. I, II and III
Answer: D
NEW QUESTION 112
Which of the following calculation is used to determine the overall tolerance for the serial combination of the component?
Response:
- A. The sum of the tolerances
- B. The average of the tolerances.
- C. The square root of the sum of the square of the tolerance.
- D. The maximum of the tolerances.
Answer: C
NEW QUESTION 113
What functions can normally be expected to be assigned to the Reliability Engineering Department of a company that emphasizes product reliability?
I. Maintain a failure reporting system.
II. Establish reliability growth.
III. Oversee use of statistical tools.
IV. Evaluate customer surveys regarding product costs.
V. Establish and maintain a corrective action system.
Response:
- A. II and III only
- B. I, III, IV and V only
- C. I, II and III only
- D. I and II only
Answer: C
NEW QUESTION 114
A standard parts program is likely to have which of the following positive and negative effects?
Response:
- A. Option B
- B. Option D
- C. Option C
- D. Option A
Answer: B
NEW QUESTION 115
In general, consumer consider reliability and safety to be a
Response:
- A. Means of reducing product cost.
- B. Characteristics of product quality.
- C. Means of reducing product liability.
- D. Characteristics of product technology.
Answer: B
NEW QUESTION 116
As the reliability engineer overseeing supplier development, you review the supplier's corrective action problem solving guidebook. It is a structured approach and you notice in the problem definition segment that there is a reference to "is data" and "is not data".
You recognize that they are using a technique promoted and championed by:
Response:
- A. Kaoru Ishikawa.
- B. Kaizen Principles.
- C. Kepner-Tregoe.
- D. Deming's PDCA Cycle.
Answer: C
NEW QUESTION 117
If the plating time of a tube increases as the inside diameter decreases, then the correlation coefficient for the insider diameter versus plating time would be:
Response:
- A. Equal to 1
- B. Greater than 1
- C. Between 0 and -1
- D. Between 0 and +1
Answer: C
NEW QUESTION 118
An intelligent and good reliability program plan is one that:
Response:
- A. Delineates the responsibilities and interfaces in as general a manner as possible.
- B. Emphasize the planning activities over the control activities.
- C. Defines in detail the complementary activities necessary for improving and assessing the reliability parameter.
- D. Retains flexibility by not formalizing reliability activities so that it cannot be tied down contractually.
Answer: C
NEW QUESTION 119
A Reliability Engineering Department is conducting a training needs assessment. Which of these techniques are used for a training needs assessment?
I. Personal observations.
II. External customer surveys.
III. Costs analysis.
IV. Work sampling.
V. Interviews.
Response:
- A. II, III and IV only
- B. I, III, IV and V only
- C. I, IV and V only
- D. I, II, III, IV and V
Answer: A
NEW QUESTION 120
Production error by human operators may be caused by:
I. Inadequate work space.
II. Inadequate job planning information.
III. Poor environmental conditions.
Response:
- A. I
- B. II
- C. All of the above
- D. I and II
Answer: C
NEW QUESTION 121
Which of the following statistical distributions can be used to compare sample means?
Response:
- A. Exponential
- B. Normal.
- C. Chi-square.
- D. t test.
Answer: D
NEW QUESTION 122
......
Updated Verified CRE Q&As - Pass Guarantee: https://prepaway.vcetorrent.com/CRE-valid-vce-torrent.html