Latest Verified & Correct Fortinet NSE7_SDW-7.0 Questions & Answers Daily Updated
100% Pass Guaranteed Download NSE 7 Network Security Architect Exam PDF Q&A
Fortinet NSE7_SDW-7.0 (Fortinet NSE 7 - SD-WAN 7.0) Certification Exam is designed for IT professionals who want to validate their knowledge and skills in designing, implementing, and managing SD-WAN solutions using Fortinet products. Fortinet NSE 7 - SD-WAN 7.0 certification exam is the highest level of certification in the Fortinet NSE 7 program and requires candidates to have a deep understanding of SD-WAN concepts, Fortinet SD-WAN solutions, and best practices for deploying and managing these solutions.
Fortinet NSE7_SDW-7.0 (Fortinet NSE 7 - SD-WAN 7.0) Exam is a certification exam that is designed for network security professionals who want to validate their knowledge and skills in implementing and managing SD-WAN solutions. NSE7_SDW-7.0 exam is part of the Fortinet Network Security Expert (NSE) program, which is a comprehensive training and certification program that is designed to help network security professionals develop the skills and knowledge they need to effectively secure networks and protect them against cyber threats.
NEW QUESTION # 13 
Exhibit B -
Exhibit A shows the system interface with the static routes and exhibit B shows the firewall policies on the managed FortiGate.
Based on the FortiGate configuration shown in the exhibits, what issue might you encounter when creating an SD-WAN zone for port1 and port2?
- A. port1 and port2 are not administratively down.
- B. port1 is assigned a manual IP address.
- C. port1 is referenced in a firewall policy.
- D. port2 is referenced in a static route.
Answer: C
NEW QUESTION # 14
Which two statements about SLA targets and SD-WAN rules are true? (Choose two.)
- A. Member metrics are measured only if an SLA target is configured.
- B. When configuring an SD-WAN rule, you can select multiple SLA targets of the same performance SLA.
- C. SD-WAN rules use SLA targets to check if the preferred members meet the SLA requirements.
- D. SLA targets are used only by SD-WAN rules that are configured with Lowest Cost (SLA) or Maximize Bandwidth (SLA) as strategy.
Answer: C,D
NEW QUESTION # 15
Refer to the exhibit.
The exhibit shows the SD-WAN rule status and configuration.
Based on the exhibit, which change in the measured packet loss will make T_INET_1_0 the new preferred member?
- A. When T_INET_1_0 has 4% packet loss.
- B. When T_INET_0_0 has 4% packet loss.
- C. When all three members have the same packet loss.
- D. When T_INET_0_0 has 12% packet loss.
Answer: C
NEW QUESTION # 16 
Two hub-and-spoke groups are connected through a site-to-site IPsec VPN between Hub 1 and Hub 2. The administrator configured ADVPN on both hub-and-spoke groups.
Which two outcomes are expected if a user in Toronto sends traffic to London? (Choose two.)
- A. Traffic from Toronto to London triggers the dynamic negotiation of a direct site-to-site VPN.
- B. The first packets from Toronto to London are routed through Hub 1 then to Hub 2.
- C. Toronto needs to establish a site-to-site tunnel with Hub 2 to bypass Hub 1.
- D. London generates an IKE information message that contains the Toronto public IP address.
Answer: A,B
NEW QUESTION # 17
Refer to the exhibit.
Based on the exhibit, which two statements are correct about the health of the selected members? (Choose two.)
- A. FortiGate can offload the traffic that is subject to passive monitoring to hardware.
- B. After FortiGate switches to active mode, FortiGate never fails back to passive monitoring.
- C. During passive monitoring, FortiGate can't detect dead members.
- D. FortiGate passively monitors the member if TCP traffic is passing through the member.
Answer: C,D
NEW QUESTION # 18
Refer to the exhibits.
Which conclusion about the packet debug flow output is correct?
- A. The packet size exceeded the outgoing interface MTU.
- B. The number of concurrent sessions for 10.1.10.1 exceeded the maximum number of concurrent sessions configured in the traffic shaper, and the packet was dropped.
- C. The total number of daily sessions for 10.1.10.1 exceeded the maximum number of concurrent sessions configured in the traffic shaper, and the packet was dropped.
- D. The number of concurrent sessions for 10.1.10.1 exceeded the maximum number of concurrent sessions configured in the firewall policy, and the packet was dropped.
Answer: B
Explanation:
In a Per-IP shaper configuration, if an IP address exceeds the configured concurrent session limit, the message "Denied by quota check" appears. SD-WAN 7.0 Study Guide page 287
NEW QUESTION # 19
Which two statements about the SD-WAN zone configuration are true? (Choose two.)
- A. You can delete the default zones.
- B. The default zones are virtual-wan-link and SASE.
- C. The service-sla-tie-break setting enables you to configure preferred member selection based on the best route to the destination.
- D. An SD-WAN member can belong to two or more zones.
Answer: B,C
NEW QUESTION # 20
Refer to the exhibit.
Which statement explains the output shown in the exhibit?
- A. FortiGate performed standard FIB routing on the session.
- B. FortiGate must re-evaluate the session due to routing change.
- C. FortiGate will not re-evaluate the session following a firewall policy change.
- D. FortiGate used 192.2.0.1 as the gateway for the original direction of the traffic.
Answer: B
NEW QUESTION # 21
Which two statements about SD-WAN central management are true? (Choose two.)
- A. It does not support meta fields.
- B. It uses templates to configure SD-WAN on managed devices.
- C. It supports normalized interfaces for SD-WAN member configuration.
- D. The objects are saved in the ADOM common object database.
Answer: B,D
Explanation:
Explanation
Normalized interfaces are not supported for SD-WAN templates. You can create multiple SD-WAN zones and add interface members to the SD-WAN zones. You must bind the interface members by name to physical interfaces or VPN interfaces.https://docs.fortinet.com/document/fortigate/7.0.0/sd-wan-new-features/794804/new-sd-wan-template-
NEW QUESTION # 22
Which SD-WAN setting enables FortiGate to delay the recovery of ADVPN shortcuts?
- A. hold-down-time
- B. link-down-failover
- C. idle-timeout
- D. auto-discovery-shortcuts
Answer: A
NEW QUESTION # 23
Refer to the exhibits.
Exhibit A -
Exhibit B -
Exhibit A shows a site-to-site topology between two FortiGate devices: branch1_fgt and dc1_fgt. Exhibit B shows the system global and system settings configuration on dc1_fgt.
When branch1_client establishes a connection to dc1_host, the administrator observes that, on dc1_fgt, the reply traffic is routed over T_INET_0_0, even though T_INET_1_0 is the preferredmember in the matching SD-WAN rule.
Based on the information shown in the exhibits, what configuration change must be made on dc1_fgt so dc1_fgt routes the reply traffic over T_INET_1_0?
- A. Disable allow-subnet-overlap under config system settings.
- B. Enable auxiliary-session under config system settings.
- C. Disable tp-session-without-syn under config system settings.
- D. Enable snat-route-change under config system global.
Answer: B
Explanation:
Explanation
Controlling return path with auxiliary session When multiple incoming or outgoing interfaces are used in ECMP or for load balancing, changes to routing, incoming, or return traffic interfaces impacts how an existing sessions handles the traffic. Auxiliary sessions can be used to handle these changes to traffic patterns.https://docs.fortinet.com/document/fortigate/7.0.11/administration-guide/14295/controlling-return-path-
NEW QUESTION # 24
What does enabling the exchange-interface-ip setting enable FortiGate devices to exchange?
- A. The tunnel ID of their IPsec interfaces
- B. The gateway address of their IPsec interfaces
- C. The IP address of their IPsec interfaces
- D. The name of their IPsec interfaces
Answer: C
NEW QUESTION # 25
Refer to the exhibits.
Exhibit A -
Exhibit B -
Exhibit A shows the SD-WAN performance SLA and exhibit B shows the SD-WAN member status, the routing table, and the performance SLA status.
If port2 is detected dead by FortiGate, what is the expected behavior?
- A. FortiGate removes all static routes for port2.
- B. Port2 becomes alive after three successful probes are detected.
- C. The administrator manually restores the static routes for port2, if port2 becomes alive.
- D. Host 8.8.8.8 is reachable through port1 and port2.
Answer: A
Explanation:
This is due to Update static route is enable which removes the static route entry referencing the interface if the interface is dead
NEW QUESTION # 26
Refer to the exhibits.
Which two statements about the IPsec VPN configuration and the status of the IPsec VPN tunnel are true? (Choose two.)
- A. The phase 1 configuration supports the network-overlay setting.
- B. Dead peer detection is disabled.
- C. FortiGate facilitated the negotiation of the T_INET_1_0_0 ADVPN shortcut over T_INET_1_0.
- D. FortiGate does not install IPsec static routes for remote protected networks in the routing table.
Answer: A,D
NEW QUESTION # 27
Refer to the exhibit.
Which configuration change is required if the responder FortiGate uses a dynamic routing protocol to exchange routes over IPsec?
- A. add-route must be disabled.
- B. mode-cfg must be enabled.
- C. exchange-interface-ip must be enabled.
- D. type must be set to static.
Answer: A
Explanation:
Explanation
for using "non ike" routes (for example BGP/static and so on) you must do disable the add-route that inject automatically kernel route based on p2 selectors from the remote site from the SD-WAN_7.2_Study_Guide page 236
NEW QUESTION # 28
Which two settings can you configure to speed up routing convergence in BGP? (Choose two.)
- A. update-source
- B. holdtime-timer
- C. link-down-failover
- D. set-route-tag
Answer: B,C
NEW QUESTION # 29
Refer to the exhibit.
In a dual-hub hub-and-spoke SD-WAN deployment, which is a benefit of disabling the anti-replay setting on the hubs?
- A. It instructs the hub to disable TCP sequence number check, which is required for TCP sessions originated from spokes to fail over back and forth between the hubs.
- B. It instructs the hub to disable the reordering of TCP packets on behalf of the receiver, to improve performance.
- C. It instructs the hub to not check the ESP sequence numbers on IPsec traffic, to improve performance.
- D. It instructs the hub to skip content inspection on TCP traffic, to improve performance.
Answer: A
NEW QUESTION # 30
Refer to the exhibits.
Exhibit A
Exhibit B
Exhibit A shows an SD-WAN event log and exhibit B shows the member status and the SD-WAN rule configuration.
Based on the exhibits, which two statements are correct? (Choose two.)
- A. FortiGate updated the outgoing interface list on the rule so it prefers port2.
- B. SD-WAN rule ID 1 is set to lowest cost (SLA) mode.
- C. Port2 has a lower latency than port1.
- D. Port2 has the highest member priority.
Answer: A,C
NEW QUESTION # 31
In the default SD-WAN minimum configuration, which two statements are correct when traffic matches the default implicit SD-WAN rule? (Choose two )
- A. An absolute SD-WAN rule was defined and matched traffic.
- B. Traffic has matched none of the FortiGate policy routes.
- C. The FIB lookup resolved interface was the SD-WAN interface.
- D. Matched traffic failed RPF and was caught by the rule.
Answer: B,C
NEW QUESTION # 32
......
NSE7_SDW-7.0 PDF Dumps Are Helpful To produce Your Dreams Correct QA's: https://prepaway.vcetorrent.com/NSE7_SDW-7.0-valid-vce-torrent.html